Product A-Z

Product overview

– GRP constructed insulated water storage tank with an AB air gap for Category 5 applications
– WRAS-approved variable speed stainless steel submersible pump(s) – mounted inside the tank to save space and allow extremely quiet operation
– High-flow solenoid valve
– Low water level pump protection device
– Digital system status display
– Fused isolation switch
– Fully tested and set up prior to delivery

Additional options

– Remote alarm panels
– Weatherproof housing
– Common alarm volt-free contact
– Horizontal split to aid access

Product overview

– Design and liaison with the local water authority
– Mechanical, electrical and commissioning of a pump station on site
– Inlet chambers, wet well and valve chambers
– ATEX-rated pumps
– Compliant control panel with GRP kiosk
– High-grade pipework and valves
– Various level control types
– Heavy-duty access covers

Additional options

– Dosing systems
– Flow meter chambers
– Combined panel for storm and foul applications
– Attenuation tanks
– Baffle plates
– Penstock valves

Product overview

– Durable steel enclosure design
– Motorised inlet valve for accurate, high-flow tank fill
– 36-litre nominal tank capacity
– Electronic controller
– WRAS approved
– Common fault volt-free contact
– Insulated tank
– Anti-pump seize function

Options

– Weatherproof version with insulated enclosure, frost stat and heater
– High-level alarm VFC
– Weir overflow catch tray with a piped outlet to waste
– Drip tray
– Wall mounting bracket

Product overview

– Industry-leading performance for its footprint
– Motorised 1” inlet valve for ultra-high top-up flow rate
– Integrated flow calming system to reduce turbulence
– Electronic pressure control
– 8-litre pressure vessel
– Common fault volt-free contact
– PurgePRO® automatic pressure vessel purge function
– Anti-seize technology
– Insulated tank

Options

– High-level alarm VFC
– High-temperature alarm VFC
– High-temperature alarm with an automatic purge
– Weir overflow catch tray with a piped outlet to waste
– Tank drain valve
– Slave tank to double capacity
– Weatherproof kiosk with frost stat, heater and consumer in
– Drip tray c/w level sensor linked to inlet cut-off

Product overview

– Variable speed controller
– Durable steel enclosure design
– Motorised inlet valve for accurate, high-flow tank fill
– 36-litre nominal tank capacity
– Volt-free contacts for common faults and pump running
– Anti-pump seize function

Options

– Weatherproof version with insulated enclosure, frost stat and heater
– High-level alarm VFC
– Weir overflow catch tray with a piped outlet to waste
– Drip tray
– Wall mounting bracket

Product overview

– Industry-leading performance for its footprint
– Single or twin pump options
– Dual full-bore motorised inlet valves for reliable ultra-high top-up flow rate
– Integrated flow calming system to reduce turbulence
– 90-litre (single pump) or 120-litre (twin pump) nominal tank capacity
– 1no or 2no 8-litre pressure vessels
– Common fault volt-free contact
– PurgePRO® automatic pressure vessel purge function
– Anti-seize technology
– Advanced EMC compatibility and power factor correction (PFC)
– Smartphone app control
– Insulated tank

Options

– High-level alarm VFC
– High-temperature alarm VFC
– High-temperature alarm with an automatic purge
– Weir overflow catch tray with a piped outlet to waste
– Tank drain valve
– Slave tank to double capacity
– Weatherproof kiosk with frost stat, heater and consumer in
– Drip tray c/w level sensor linked to inlet cut-off

Product overview

– Temperature range up to 120°C (when using intermediate cooling vessel)
– Cold fill pressure 0.8 bar to 3.5 bar (AP3) or 3.5 bar to 7.0 bar (AP7) and 7.0 bar to 9.0 bar (AP9)
– Reliable 2020Plus Microprocessor/transducer control
– Boiler/chiller safety interlock relay
– Audible alarm with mute & reset operates on high and low pressure
– Expansion vessels – max working pressure 10 bar and 16 bar
– Twin pump models with duty/standby pumps & automatic alternation of duty pump to even wear
– Fluid category 5 (Water Supply Regulations 1999)
– Designed and built to the latest CE requirements and in accordance with ISO9001
– Leak detection via the frequency of starts alarm

SIZING

The size of the dosing pot installed in a system is not critical as multiple doses of chemicals can be put into the system to reach the correct concentration. A smaller unit is easier to handle physically and allows for more accurate dosing. However, the time on site for performing multiple doses has to be considered; this factor should influence your decision when selecting dosing pots.

Note: Chilled water systems often require large volumes of glycol to be dosed into the system; a larger dosing pot may be required for chilled water systems.

The formula below can be used as a guide to help you in your selection:
Boiler power (kW) x 12 litres/kW x 0.01 (based on 1% concentration*) = volume of chemical required

Example: Boiler power 250 kW x 12 litres x 0.01 = 30 litres of chemical.

You could use any of the following dosing pots for this installation:
– 5 litre – dose six times
– 10 litre – dose three times
– 15 litre – dose two times

*Confirm the required concentration level for the chemical being used.

CK Control Panel

– Hard-wired control panel
– A premium duty/standby steel control panel, complete with hand/off/auto switches, run & trip lamps, mains isolator, control health lamp and BMS contacts
– Suitable for integrals SMS autodial alarm system

EPIC Control Panel

– PCB board control panel
– Suitable for clear and wastewater applications
– Works with float switches, pressure switches and probes
– Self-learning of the pump data (sets overloads), duty/standby logic
– BMS input, minimum and maximum water level alarm
– Phase failure, dry running protection and alarm
– Water in oil chamber protection and alarm
– Pre-fitted with a rotary isolator

Vortech® Battery Alarm

– Dutypoint Vortech® Battery Alarm c/w 10 m float switch
– Battery-powered high-level alarm panel with test and mute buttons

Sewage for Adoption Panel

– Type 3 panel
– Surge protection device
– Ultrasonic controller
– A multi-function power meter on the incomer with a pulsed energy signal to telemetry
– Intrinsically safe barrier relay for the backup float circuit
– Non-powered IS barrier for the high-level float
– Brown out reset timers on fail-safe circuits
– Over-temperature lockout circuits from bi-metallic switches in the pumps
– Seal leak indication and volt-free signals utilising conductivity relays (no protection at this stage)
– Dry run protection by load monitors
– Telemetry signal requirements for Type 3 pumping stations
– Personnel on-site switch on the control section door wired to the telemetry marshalling terminals
– Set of telemetry marshalling terminals with a twisted pair multicore screened cable connected to them and left flying in the kiosk for connection to the telemetry equipment by others
– 17. 110 V lifting hoist supply with an isolator socket in the main kiosk

SMS Remote Monitoring Panel

– To provide text/email alarm notifications
– Up to 10no. individual programmable alarm outputs and up to 3no. alarm contacts (additional contacts)
– Pre-programmed to your requirements and tested before dispatch
– Ability to remotely access the historic event log
– 230 V AC or 24 V DC power supply options
– Includes power failure alarm c/w side-mounted stub antenna
– 2G mobile network connectivity is required. Extension antenna cables are available on request for basements with limited connectivity

Galvanised fabricated steel

– Available in all load ratings
– Bespoke sizes available
– Not suitable for highway

Galvanised pressed steel

– Available in load rating up to FACTA B
– Off the shelf standard sizes only
– Pedestrian loading only

Composite

– Standard 450 mm Ø, other sizes available
– Pedestrian loading only

Ductile iron

– For highway applications (fast moving traffic)
– Standard sizes only
– Available with sealing plates for pressure resistance or odour protection

Specials

– Spring-assisted lift
– Safety grids
– Multi-section
– Removable support beams
– Stainless steel
– Post and barrier kits
– Water industry specification

Recessed

– Available to suit different infill types: Block paving, grass, screed, interior tiling
– Available in all load ratings
– Option of decorative drims

STANDARD TECHNICAL FEATURES

– Efficient removal of air and microbubbles in pipework
– Stainless steel element
– Designed and manufactured in accordance with the Pressure Equipment Directive 97/23/EC

OPTIONS

– Larger units up to DN600 available on request
– Non-standard connections

STANDARD TECHNICAL FEATURES

– Efficient removal of air and microbubbles in pipework
– Effective removal of impurities and particles
– Stainless steel element
– Designed and manufactured in accordance with the Pressure Equipment Directive 97/23/EC

OPTIONS

– Removable element (CXC-RE)
– Larger units up to DN600 available on request
– Non-standard connections

NOTE

– The static head must not exceed 15 m for a heating system and 5 m for a cooling system

STANDARD TECHNICAL FEATURES

– Efficient removal of particles in pipework
– Stainless steel element
– Designed and manufactured in accordance with the Pressure Equipment Directive 97/23/EC

OPTIONS

– Removable element (-RE models)
– Larger units up to DN600 available on request
– Non-standard connections

STANDARD TECHNICAL FEATURES

– Efficient removal of air and microbubbles in pipework
– Effective removal of impurities and particles
– Stainless steel element
– Designed and manufactured in accordance with the Pressure Equipment Directive 97/23/EC
– Enables perfect hydraulic balance between primary and secondary circuits

OPTIONS

– Non-standard connections
– Larger units up to DN600 available on request

STANDARD TECHNICAL FEATURES

– WRAS approved for potable water
– High build quality and 10-year guarantee
– Effect of treatment lasts for at least seven days
– No corrosive elements added to the water
– Low power consumption
– No regeneration process required
– No chemicals to top up. No routine maintenance required
– Economical installation – no separate mains supply required for water
– No straight pipework required either side of unit
– Unit is pre-wired with wall-mountable control box
– Versatile installation

Options

– Water meter
– Mounting bracket
– Isolation valves
– Bypass assembly
– Particle filtration
– Flanged connections
– Duplex connection kits
– Common fault volt-free contact

Standard technical features

– 28 mm connections for high flow rates
– 4.5 bar and 6.0 bar versions for high-pressure installations
– WRAS approved for potable water
– Expansion vessel and two-port motorised zone valve included
– 3 kW electric immersion heater in addition to the primary coil
– ½” hot-water secondary return as standard
– High-performance insulation minimises energy loss
– High-grade duplex stainless steel construction for excellent durability
– 22 mm or 28 mm diameter stainless steel heating coil for fast reheating times
– Durable plastisol casing
– Factory-fitted pressure and temperature relief valve

Approvals

– Building Standards: BS 853-1-1996 & BS-12-897
– Building Regulations: Part G & L

Guarantee

– Internal cylinder: 25 years
– Ancillary components: 1 year

Options

– Uprated primary coil for faster recovery times (available on 175-litre and larger models)
– 6 kW immersion heater (standard on Pro versions)
– Twin immersion heaters
– 1” hot-water secondary return
– Non-standard sizes
– Direct cylinders (immersion heater only)